Top 10 Rand Mcnally Dash Mount Disc

The APVHB20 90mm adhesive mounting disk features an extra-strength 3M VHB adhesive and allows you to securely mount an Arkon or third-party 80mm windshield suction mounting pedestal to your car’s dashboard. Applicable Arkon mounting pedestal models include CM017-KST-2SH, CM078WD-SBH, RM080AMPS, RM0792TWD, and RM0802T. (Note that the disc is meant to be a bit larger than the mount to ensure a secure fit.) This package includes only the extra-strength adhesive disk (mounting pedestals sold separately). To apply the adhesive disk to the car’s dashboard, simply remove the paper backing from the back of the plastic 3M VHB dash mount disc, then place and press down on a previously cleaned surface. (Allow 24 hours for the adhesive to cure before securing the base of the mounting pedestal to the center of the disk for best results.) WARNING: Use caution and discretion when adhering APVHB20 to your car dashboard or other flat surface. This disk uses 3M VHB adhesive, which is designed to be a PERMANENT solution. Use of this disk may result in permanent adherence to the selected surface. Professional strength solvents or tools may be helpful in removing the adhesive. Arkon is not responsible for any damage caused to your vehicle or other surface due to the installation of this mounting disk. Adhesive disks with a semi-permanent bonding strength (Model AP036 -70mm, Model AP013 -80mm, Model AP020 -90mm) are available from Arkon. For an extra-strength 80mm disk to use with 70mm suction mounts, see Arkon Model APVHB13.

Securely hold your OverDryve, TND, or other dashboard devices with the low-profile Crescent Bean Bag Dash Pad. The pad grips the dash when in use, but is easy to take on and off.

Securely holds in place suction-cup mounted devices (89 mm or 3 1⁄2” suction cups)
The steel-weighted 2.2-pound base has an anti-skid, silicone rubber underside; which keeps the pad in place
Easy to install—the pad is portable, enabling easy transfer between cars or stowing away when not in use

The AP020 90mm adhesive mounting disk allows you to mount an Arkon or third-party 80mm windshield suction mounting pedestal to your car’s dashboard, including mounting pedestals for Garmin and TomTom GPS devices. (Note that the disc is meant to be a bit larger than the mount to ensure a secure fit.) This package includes only the adhesive disk (mounting pedestals sold separately). To apply the adhesive disk to the car’s dashboard, simply remove the paper backing from the back of the plastic 3M dash mount disc, then place and press down on a previously cleaned surface. (Use included alcohol pad to ensure mounting area is clean and free of any dashboard conditioners or other treatments. For best results, allow 24 hours for the adhesive to cure before securing the base of the mount to the center of the disk.) While this disk is meant to be a semi-permanent solution, the disk can be removed from the dash by applying a generous amount of rubbing alcohol or similar adhesive removal product to the area with a cotton swab. Let the liquid saturate the area, then work a long piece of dental floss under the disk to cut through the adhesive until the disk is removed. For an 80mm disk to use with 70mm suction mounts, see Arkon Model AP013. For a 70mm disk to use with 60mm suction mounts, see Arkon Model AP036.

Worried that your suction cup mount will damage your dashboard?
Mounting your GPS, cell phones and other devices on the car dashboard or windshield is essential while driving. It allows you to conveniently view your messages without taking your eyes off the road.

However, the mounting pedestals and suction holders of these electronics can be sticky. When placed on textured or soft dashboards, they can damage the surface. Plus, they leave a residue once you decide to remove them.

Protect your dash from adhesive remnants with Crossery Adhesive Mounting Disk!

This car accessory fits any 60mm suction mount for smartphones, car cameras and GPS. The disk adheres to the dashboard, while the suction cup holds on to the disk. With a much larger size than the cup, it ensures a secure attachment so that the pedestal won’t fall off.

The strong adhesive ensures that your device won’t drop even if it is placed on your windshield. It will not melt or lose its strength under the heat of the sun.

Don’t worry about upgrading your devices in the future, when you would need a larger disk. We used a semi-permanent adhesive that can be detached as easily as it is set up.

Here are more benefits of using our mounting disk:

? Also comes in larger sizes of 80mm and 90mm to suit your needs
? The disk is compact and won’t take up too much space on your dashboard
? A practical gift for friends and family on any occasion
? Backed with a 2-year warranty
Mount your devices on the dashboard safe and secure. Add Crossery Adhesive Mounting Disk to your cart TODAY!

Universal Compatibility
About 70mm diameter fits for almost all Garmin TomTom Magellean GPS mounting pedestals and dashboard suction phone mount.

Dashboard Mounting Instructions
1. Choose a suitable location for disk (and pedestal) installation.
Do not place mount in or near an air bag deployment zone or where it will obstruct view of the road or hinder vehicle operation.
2. Clean the dashboard surface area thoroughly with alcohol pad to ensure dashboard is clean and free of any dashboard conditioners or other treatments.
3. Remove the paper backing of the disk and place on the cleaned surface. Press the top of the disk down firmly to allow the adhesive to stick to the surface. Allow 24 hours for the adhesive to cure to the surface before applying any pressure.
4. Place the suction cup of the pedestal (sold separately) firmly down on the center of the mounting disk and lower the securing lever.

Removal Instructions
1. Prepare the surface around the disk by applying a generous amount of rubbing alcohol or similar adhesive removal product to the area with a cotton swab. Let the liquid saturate the adhesive area for about a minute.
2. Take a long piece of dental floss in each hand and slowly work back and forth at the base of the adhesive disk. Gently use the dental floss to cut the adhesive from the dashboard until the black plastic disk is removed.
3. If the sticky adhesive area breaks apart or does not come off completely, re-apply a small amount of alcohol (or adhesive removal liquid) and carefully lift off the remaining area by hand.

Note: Adhesive disk is intended for semi-permanent installation and one-time application. Once removed, it can’t be reapplied.

Package
2 * 70mm Adhesive Mounting Disk

The AP013 80mm adhesive mounting disk allows you to mount an Arkon or third-party 70mm windshield suction mounting pedestal to your car’s dashboard, including Arkon’s mounting pedestal models GN079WD-SBH, GN068WD-SBH, GN022-SBH, GN014-SBH, GN015-SBH, and GN042-SBH. (Note that the disc is meant to be a bit larger than the mount to ensure a secure fit.) This package includes only the adhesive disk (mounting pedestals sold separately). To apply the adhesive disk to the car’s dashboard, simply remove the paper backing from the back of the plastic 3M dash mount disc, then place and press down on a previously cleaned surface. (Use included alcohol pad to ensure mounting area is clean and free of any dashboard conditioners or other treatments. For best results, allow 24 hours for the disk adhesive to cure on the dashboard before securing the base of the mount to the center of the disk.) While this disk is meant to be a semi-permanent solution, the disk can be removed from the dash by applying a generous amount of rubbing alcohol or similar adhesive removal product to the area with a cotton swab. Let the liquid saturate the area, then work a long piece of dental floss under the disk to cut through the adhesive until the disk is removed. For a 90mm disk to use with 80mm suction mounts, see Arkon Model AP020.

Package included:

1x 105mm Adhesive Mounting Disk;

2x 75mm Adhesive Mounting Disk

Warranty:

24-month warranty.

Note:

1.It is suggested to allow 24 hours for the adhesive to solidify before securing the base of the mount to the center of the disk

2.How to remove: Saturate the area with Medicinal alcohol or other adhesive removal product, then scrape the adhesive with a dental floss

Any questions you have, please feel free to contact us. We will get you back within 24 hours.

The AP036 70mm adhesive mounting disk allows you to mount an Arkon or third-party 60mm windshield suction mounting pedestal to your car’s dashboard, including mounting pedestals for Garmin and TomTom GPS devices. (Note that the disc is meant to be a bit larger than the mount to ensure a secure fit.) This package includes only the adhesive disk (mounting pedestals sold separately). To apply the adhesive disk to the car’s dashboard, simply remove the paper backing from the back of the plastic 3M dash mount disc, then place and press down on a previously cleaned surface. (Allow 24 hours for the adhesive to cure before securing the base of the mounting pedestal to the center of the disk for best results.) While this disk is meant to be a semi-permanent solution, the disk can be removed from the dash by applying a generous amount of rubbing alcohol or similar adhesive removal product to the area with a cotton swab. Let the liquid saturate the area, then work a long piece of dental floss under the disk to cut through the adhesive until the disk is removed. For an 80mm disk to use with 70mm suction mounts, see Arkon Model AP013. For a 90mm disk to use with 80mm suction mounts, see Arkon Model AP020.

The 70 mm round console disk can transform any windshield mount into a console mount. The 3M adhesive is strong yet leaves no residue when removal is required.