The Best Frigidaire Dishwasher Panel Console

This is an authorized aftermarket product. Fits with various Electrolux Brand models. It has a OEM Part # 807545704.

Product Description

This is a genuine replacement part. The model number and name for the following item is: Frigidaire (FRIGB) 5304478319 Touchpad And Control Panel.

From the Manufacturer

This is a genuine replacement part. The model number and name for the following item is: Frigidaire (FRIGB) 5304478319 Touchpad AndControl Panel

Dishwasher bottom door gasket and deflector strip. If the dishwasher is leaking, the gasket may be damaged.

Product description

154754502 Upper Spray SAME AS 5304506516

From the Manufacturer

Frigidaire 154754502 Upper Spray Arm Assembly for Dish Washer. This spray arm simply screws into the top of your dishwasher tub. This part is actually two pieces, the spray arm and mounting nut. The spray arm simply snaps into the mounting nut, but it is already assembled. Approximately 9.5-Inch Long. Genuine replacement part.

Genuine Original Equipment Manufacturer (OEM) parts! This spray arm (part number 154567702) is for dishwashers. Spray arm 154567702 rotates and sprays water to clean the dishes inside the dishwasher tub. Wear work gloves to protect your hands during this repair. For Kenmore, Frigidaire, & White-Westinghouse.

Genuine Original Equipment Manufacturer (OEM) parts! This door spring (part number 154579101) is for dishwashers. Door spring 154579101 applies tension to the dishwasher door through the door hinge to prevent the door from dropping too quickly when you open the dishwasher. Use caution when installing the door spring because the spring is under tension and could snap. Wear work gloves to protect your hands during this repair. For Frigidaire, Crosley, & Kenmore.

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) and turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw or one of new provided screws. 4) Push dishwasher back into place. Open dishwasher door. Determine which bracket hole you will use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If you need to use back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher back into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in the tub. Use a sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 inch hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a nice clean hole without damaging the tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into the cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal. This is a generic product manufactured & distributed by Impresa Products (TM). This is not a Frigidaire (TM) / Electrolux (TM) OEM product. Any use of Frigidaire (TM) or Electrolux (TM) brand names, models, etc. are made solely to describe & illustrate compatibility.

From the Manufacturer

Frigidaire 154319706 Rack Assembly for Dish Washer. Works with models: 12-1063-00-04, 2-1063-23-04, 12-1063-45-04, 2-1063-57-04, 12-1063-66-04. Genuine replacement part.